EDIOM SPORTSGrip donuts for team garages
Factory guide · grip donuts

Custom grip donuts for motorcycle racing teams and track-day merch

A grip donut is a flat neoprene ring that sits at the inner end of a handlebar grip. For a racing team, a track-day club or a riding school, it is also one of the smallest pieces of kit that can carry team colours, a rider number or a sponsor mark. This guide shows how EDIOM SPORTS, a neoprene factory in Huizhou, China, plans a team run: the reference size, how to count pairs per design, which print route suits which artwork, and how pairs are packed for a merch table.

Quick facts: reference ring 55 mm outer, 25 mm opening, 5 mm thick; one pair = two rings; the custom minimum is confirmed per design. The neoprene material is SGS/RoHS tested. Full details are on the official motorcycle grip donut page; questions go to sales2@ediom.net.

A pink leopard-print neoprene grip donut being positioned at the inner end of a brown handlebar grip, next to the switch housing
In use: a printed ring positioned at the inner end of a sample grip. Match the ring to your own grip and controls before you order.
EDIOM grip donut product film, about 44 seconds: fitting a ring on a grip, the 55 mm and 25 mm measurements, several print designs and pair packs. Open the MP4.

55 mm reference ring: grip donut fit for team bikes

Every team run starts with one measurement. EDIOM's reference ring is 55 mm across, with a 25 mm opening and 5 mm of neoprene between fabric faces. That is a starting point, not a promise for every bike: grips, inner flanges and switch housings differ between models, and a ring that sits well on one bike can crowd the controls on another.

Size chart of a pink printed grip donut and a black grip donut beside a coin: outer diameter 55 mm, inner diameter 25 mm, thickness 5 mm
Spec: the reference ring, 55 mm outer diameter, 25 mm inner diameter, 5 mm thick. Any custom cut size and the thickness are agreed on the sample.

A fit check that works for a mixed paddock

  1. List every bike model the run is for. Team bikes, practice bikes and riders' own road bikes can all have different grips.
  2. For each model, photograph the grip and measure its diameter where the ring will sit.
  3. Note the clearance between the grip end and the controls.
  4. Send the photos and measurements with your quantity in pairs. EDIOM checks them against the reference ring.
  5. Approve the fit on a physical sample: the ring should seat on the target grip and the controls should move freely.
Reference specificationValue (official product page)
MaterialNeoprene with fabric faces
Outer diameter reference55 mm
Inner opening reference25 mm
Thickness reference5 mm
ShapeFlat ring with cut inner and outer edges
Order unitOne pair = two rings

The neoprene material is SGS/RoHS tested. Final dimensions, material thickness and packing are confirmed against your approved sample.

Team-colour grip donut designs for rider and sponsor merch

A team usually needs more than one design: a team-colour ring for the race bikes, perhaps one per rider, and a version for the merch table. Each design is counted separately, so decide the split before you ask for a quote.

Two grip donuts beside a red flame-pattern grip: one with a white skull print on the face, one plain black
Product display: a printed face beside a plain black ring. Printed examples have artwork on one face and a black reverse, so say which faces you want printed.

Pick the print route by artwork

Full-colour sublimation
For all-over artwork, such as a full team livery pattern, on a suitable light fabric. Check the cut outline, print margins and colour references on the sample.
Screen printing
For logos and spot-colour designs such as a team badge or rider number. Print size, colour count and fabric decide the setup.
Solid colour / unprinted
Keep the surface plain, or add labels and other branding separately. Custom fabric or trim may have its own minimum.

Logos and repeating patterns need a layout around the central opening, and key artwork should stay clear of both cut edges.

A purple grip donut with a repeating white EDIOM logo print overlapping a plain black grip donut
Multiple designs: a repeating logo print, the kind of layout a team badge or sponsor name can follow, next to a plain black ring.
Several grip donuts in leopard, grey skull and stars-and-stripes flag prints spread out on a white surface
Multiple designs: leopard, skull and flag prints from one production setup. Printed examples show possibilities, not stocked offers.
Teal, red and brown sprinkle-pattern grip donuts arranged around a red flame-pattern handlebar grip
Multiple designs: one shape, several colourways. A team can keep one layout and change only the colours for each rider.
A pair of white unprinted grip donuts with black edges on a white background
Product display: white-faced rings for printing. White unprinted pairs are listed on the ready-to-ship page for teams that want to test their own DIY sublimation artwork first.

Ordering grip donuts in pairs for a racing team

Grip donuts are quoted in pairs: one pair is two rings, one for each grip. Write quantities as pairs per design, and say whether each pair is matching or mixed. Grips, bikes and display props are not included.

Team grip donut order planner: a 55 mm reference ring drawing and a table of brief lines covering order unit, design split, surface, print route, faces, packing, minimum and trial pairs
Spec: a one-page planner for a team brief. Every figure on it comes from the official product and ready-to-ship pages.

Five lines for a first team brief

  1. Bikes and fit: grip photos, the diameter at the ring position and the clearance, per model.
  2. Designs: how many designs (team, rider, merch) and the artwork for each, as AI, PDF, EPS, CDR or a high-resolution JPG.
  3. Print route and faces: sublimation, screen print or solid colour, and which faces to print.
  4. Quantity: pairs per design. EDIOM confirms the custom minimum for your print, material and packing before quoting.
  5. Packing and date: bag, header card or bulk packing, the destination and the date you need the rings at the track.

Pair packs for a merch table

Two packs of sprinkle-print grip donuts, each with a pair of rings in a clear bag with an EDIOM header card, resting on a black motorcycle seat outdoors
Packaging scene: pairs individually wrapped in a bag with a header card. Bags and header cards are optional presentation choices, agreed and quoted separately; your own brand can go on the card.

Want to see the material before committing? White unprinted pairs on the ready-to-ship page have a minimum trial order of one pair; confirm current quantities and dispatch with sales. A reference sample or a custom pre-production sample can also be discussed, with cost and timing confirmed for your project.

Questions team managers usually ask

Will the 55 mm ring fit every bike in our team?

Not automatically. The 55 / 25 / 5 mm figures describe the reference ring and do not establish fit for every bike. Send a grip photo, the diameter at the ring position and the clearance for each model, and approve installation on the target grip.

What is the minimum for our own design?

It is confirmed per design, in pairs, after EDIOM sees your print, material and packing choices. Tell sales2@ediom.net the quantity per design.

Can each rider have a different design?

Yes. Each design is planned and counted separately, so list the pairs you need for each one.

Can the packaging carry our team brand?

Yes, subject to the agreed specification and supplier minimums. Individual bags, header cards, hang tags, labels and carton marks are quoted separately.

Has the material been tested?

The neoprene material is SGS/RoHS tested. Ask sales2@ediom.net if you need more detail for your project.

How fast can we get them for a race date?

No fixed lead time is published. Timing depends on the approved design, materials, quantity and destination, so include your required arrival date and EDIOM will confirm the sample, production and shipping plan with the quotation.

Who makes these grip donuts

EDIOM SPORTS (惠州市阿贝斯特运动用品有限公司, Huizhou Ediom Sports Co., Ltd.) was established in Huizhou, Guangdong, in 2014 by the founding team of Shenzhen EDIOM, which began working with neoprene products in 2008. EDIOM SPORTS makes made-to-order neoprene products; the appearance, printing and stitching of every finished piece are checked, with other checks sampled during production.

Address: 2nd Floor, Building 1, Weihao Industrial Park, Tangxia, Chanjing Village, Xinxu Town, Huiyang District, Huizhou, Guangdong, China. Visits are by appointment.

Besides grip donuts, the same factory makes neoprene coffee sleeves, can coolers and PU leather can coolers; the full range is on www.ediom.com.cn.